NSN Search by National Stock Number
Search the MCRL (Master Cross-Reference List) provided by the FLIS (Federal Logistics Information Service) through the DLA (Defense Logistics Agency) of the DOD (Department of Defense). FLIS provides this data through their WebFLIS and FEDLOG products, but these are not available for public use. This free NSN Search provides NSN lookup of the Military NSN Database by National Stock Number.
The NSN Lookup search engine allows you to easily search for National Stock Numbers (NSN) over all of the catalogs and databases available within NATO for public use:
About 1001 results (0.05 seconds)
- 6520-00-470-8293 REFLECTOR,DENTAL LIGHTMore Info ...
- END ITEM IDENTIFICATION
- LIGHT,DENTAL OPERATING,CEILING
- GENERAL CHARACTERISTICS ITEM DESCRIPTION
- GLASS,COLOR CORRECTING TO 380-0.0 DEG KELVIN,FRONT SURFACE WITH DICHORIC COATING,REAR SURFACE WITH CERAMIC FRIT COATING; 10.125 IN. LG,4.500 IN. W; 4.375 IN. H
- PURCHASE DESCRIPTION IDENTIFICATION
- 46308-H39-022438
- PART NAME ASSIGNED BY CONTROLLING AGENCY
- REFLECTOR DENTAL LIGHT GLASS 10.125IN LG COLOR CORRECTING
- UNIT OF ISSUE CUBE
- 0.007 CUBIC FEET
- 5120-01-187-5715 PULLER,MECHANICALMore Info ...
- FUNCTIONAL DESCRIPTION
- FDESIGNED FOR USE DURING REMOVAL OF TWO BALL BEARINGS FROM THE ALTERNATOR GEARSHAFT OF THE F107-WR-101 ENGINE AND ONE BEARING FROM THE SPUR IGNITIONGEARSHAFT OF THE F107-WR-102 AND F107-WR-400 ENGINE
- STYLE DESIGNATOR
- GEAR AND BEARING, SINGLE END GRIP TWO JAW, EXTERNAL
- 4935-01-187-5704 TEST SET,GUIDED MISSILEMore Info ...
- TEST TYPE FOR WHICH DESIGNED
- GROUND FUNCTIONAL TEST
- INCLOSURE FEATURE
- MULTIPLE ITEM W/CARRYING CASE
- MAJOR COMPONENTS
- BOX ASSY;SYNTHESIZER ASSY;CONTROL ASSY;POWER CABLE ASSY;UMBILICAL CABLE ASSY;GSE CABLE ASSY;BATTERY SIMULATOR CABLE ASSY;RF CABLE ASSEMBLY
- END ITEM IDENTIFICATION
- AN/DSM-160
- 5120-01-187-5713 PULLER,MECHANICALMore Info ...
- FUNCTIONAL DESCRIPTION
- DESIGNED FOR USE DURING REMOVAL OF THE RADIAL COMPRESSOR ROTOR INSTALLED ON THE HIGH PRESSURE TURBINE SHAFT
- STYLE DESIGNATOR
- SLIDE HAMMER, GEAR AND BEARING THREE JAW EXTERNAL
- 5998-01-187-5668 CIRCUIT CARD ASSEMBLYMore Info ...
- END ITEM IDENTIFICATION
- AN/FPS-115 RADAR SET
- CRITICALITY CODE JUSTIFICATION
- CBBL
- FEATURES PROVIDED
- ELECTROSTATIC SENSITIVE
- SPECIAL FEATURES
- PWB 1,CAP 79,MC 71,PLUG 1,RES 2
- 1730-01-187-5872 STAND,AIRCRAFT ENGINEMore Info ...
- DESIGN TYPE
- STAND OR DOUBLE ARM
- OVERALL HEIGHT
- 18.000 INCHES NOMINAL
- OVERALL LENGTH
- 29.000 INCHES NOMINAL
- OVERALL WIDTH
- 24.000 INCHES NOMINAL
- 1260-01-187-5780 LOWER SHROUD ASSEMBMore Info ...
- GENERAL CHARACTERISTICS ITEM DESCRIPTION
- JCONSISTING OF 1 SUPPORT PAD,1 SUPPORT,4 SHIMS,1 HOUSING,2 BUMPERS,2 SPACERS,2 BRACKETS,1 SHELL,3 FLANGES,1 SUPPORT CONNECTOR,1 SUPPORT ALLIGNMENT PIN,176 WASHERS,192 E-Z BUCK RIVETS,6 RECEPTACLES,40 NUT PLATES
- 7025-01-187-5384 TERMINAL,DATA PROCESSINGMore Info ...
- VOLTAGE IN VOLTS AND CURRENT TYPE
- 120.0 AC
- SPECIAL FEATURES
- USES A RS-232-C INTERFACE; CURRENT RATING IN AMPS:1.8; OPERATING RANGE:OPERATES AT 300 BAUD; THERMAL PRINTER PRINTS 45 CHARACTERS PER SECOND ON 80 OR 132 CHRACTER LINE; POWER SOURCE:EXTERNAL; MAXIMUM O/A WIDTH:11.700 IN.; MAXIMUM O/A HEIGHT:2.7000 IN.; FREQ IN HERTZ:60.0
- 5998-01-187-5203 CIRCUIT CARD ASSEMBLYMore Info ...
- OVERALL HEIGHT
- 0.682 INCHES MAXIMUM
- OVERALL LENGTH
- 7.000 INCHES NOMINAL
- OVERALL WIDTH
- 6.000 INCHES NOMINAL
- SPECIAL FEATURES
- CAPACITOR 15; COIL 3; CONNECTOR 1; CONNECTOR,TEST POINT 5; DIODE 16; HEAT SINK 1; PRINTED WIRING BOARD 1; RESISTOR 38; TRANSISTOR 9
- 4320-01-187-5004 RING,WEARINGMore Info ...
- END ITEM IDENTIFICATION
- VARIOUS SUBMARINE PUMPS
